Skip to main content
Home/Math, Geometry & STEM Science Utilities/RLC Bandpass / Bandstop Circuit Quality Factor (Q) & Bandwidth Sizer

RLC Bandpass / Bandstop Circuit Quality Factor (Q) & Bandwidth Sizer

Calculate resonant frequency, Quality Factor (Q), -3 dB half-power bandwidth, exact cutoff frequencies, damping ratio, and Bode response for Series and Parallel RLC bandpass and bandstop filters.

Circuit Topology & Component Parameters

Engineering Workflow Mode
Network Topology
Filter Transfer Type
Passive Component Values (R, L, C)Q = Z₀ / R
Active Equivalent Circuit SchematicSeries Loop • BPF
VinR=50.000 ΩL=10.000 mHC=253.300 nFVoutVout taken across R (Pass at f₀)
Load Engineering Circuit Preset
Exact Quadratic Cutoff Solver2nd-Order Linear Network

Resonance, Q-Factor & Bandwidth Analysis

Quality Factor (Q)MODERATE SELECTIVITY
3.97dimensionless

Damping Ratio (ζ): 0.1258

Fractional BW: 25.16%

-3 dB Half-Power Bandwidth
795.775 Hz

Center f₀: 3.162 kHz

ω₀: 19.869 krad/s

Lower Cutoff (fL)2.789 kHz-3.01 dB point
Upper Cutoff (fH)3.585 kHz-3.01 dB point
Tank Z₀ = √(L/C)198.693 ΩXL = XC at f₀
Bandpass Magnitude Response |H(jf)|0 dB to -40 dB Scale
0 dB-3 dB-20 dB-40 dBf₀ (1.0×)0.25·f₀2.0·f₀
Gain: 0.00 dB (100.0%) | Phase: 0.0°
Transient Damping & Ringing BehaviorUnderdamped (Oscillatory)
Damping Ratio (ζ)0.1258
Attenuation (α)2500.0 Np/s
1/e Ringing Decay1.26 cycles
Low-Q Asymmetry Note: Because Q < 10, fL and fH are geometrically symmetric around f₀ (f₀ = √(fL·fH)) rather than arithmetically centered.

RLC Resonance Theory: Series vs. Parallel Quality Factor Equations

In second-order passive analog filter design, resonance occurs at the exact angular frequency ω₀ where inductive reactance (XL = ωL) equals capacitive reactance (XC= 1/ωC). At this frequency, reactive energy oscillates cleanly between the inductor's magnetic field and the capacitor's electric field, leaving the circuit's net terminal impedance purely resistive.

f₀ = 1 / (2π · √(L · C))   |   Z₀ = √(L / C)   |   BW-3dB = f₀ / Q = fH - fL

While the resonant frequency f₀ and characteristic tank impedance Z₀ = √(L/C) are identical for both configurations, the role of resistance R in dissipating energy is inverted between Series and Parallel networks:

ParameterSeries RLC NetworkParallel RLC TankPhysical Significance
Quality Factor (Q)Q = (1/R) · √(L/C) = Z₀ / RQ = R · √(C/L) = R / Z₀2π × (Peak Stored Energy / Energy Dissipated per Cycle)
-3 dB Bandwidth (BW)BW = R / (2πL)BW = 1 / (2πRC)Frequency span between half-power (-3.01 dB) points
Damping Ratio (ζ)ζ = (R/2) · √(C/L) = 1/(2Q)ζ = (1/2R) · √(L/C) = 1/(2Q)Governs transient step overshoot and oscillation decay
Impedance at f₀Zmin = R (Minimum)Zmax = R (Maximum)Series draws max current at f₀; Parallel blocks current at f₀

Half-Power Cutoff Frequencies (fL, fH) & Low-Q Asymmetry

A common shortcut in textbook approximations assumes that the lower and upper -3 dB cutoff frequencies sit symmetrically at f₀ − BW/2 and f₀ + BW/2. In physical RLC networks, however, the magnitude response is symmetric on a logarithmic frequency axis, meaning f₀ is the geometric mean rather than the arithmetic mean of the two cutoff frequencies:

fL = f₀ · [ √(1 + 1/(4Q²)) − 1/(2Q) ]
fH = f₀ · [ √(1 + 1/(4Q²)) + 1/(2Q) ]
f₀ = √(fL · fH)   and   BW = fH − fL = f₀ / Q

When Q ≥ 10 (narrowband RF, IF, and ultrasonic resonators), the term 1/(4Q²) is less than 0.0025, so the arithmetic approximation matches exact values within 0.12%. In wideband audio crossovers or low-Q power line filters where Q < 2, relying on f₀ ± BW/2 produces severe center-frequency skew and improper stopband roll-off—and when a gentle single-pole low-pass or high-pass slope suffices without resonant peaking, you can size a 1st-order stage directly using our RC & RL Circuit Cutoff Frequency Solver.

Worked Analog Filter Sizing Examples

Example 1: 455 kHz AM IF Bandpass FilterHigh-Q Selective
  • Design Target: f₀ = 455 kHz, BW = 10 kHz, R = 15 Ω
  • 1. Required Q = f₀ / BW = 455 kHz / 10 kHz = 45.5
  • 2. ω₀ = 2π × 455,000 = 2.8588 × 10⁶ rad/s
  • 3. Series L = (Q · R) / ω₀ = (45.5 × 15) / 2.8588e6 = 238.7 µH
  • 4. Series C = 1 / (ω₀² · L) = 512.7 pF
  • Result: f_L = 450.03 kHz, f_H = 460.03 kHz (ζ = 0.011)
Example 2: Parallel Tank RF Amplifier LoadParallel Tank
  • Components: R = 4.7 kΩ, L = 100 nH, C = 25.33 pF
  • 1. f₀ = 1 / (2π · √(100e-9 × 25.33e-12)) = 100.0 MHz
  • 2. Tank Z₀ = √(100e-9 / 25.33e-12) = 62.83 Ω
  • 3. Parallel Q = R / Z₀ = 4700 / 62.83 = 74.80
  • 4. -3 dB BW = 100.0 MHz / 74.80 = 1.337 MHz
  • Result: Rejects out-of-band harmonics with 74.8× selectivity

Frequently Asked Questions (FAQ)

What is the Quality Factor (Q) in an RLC resonant circuit?

The Quality Factor (Q) is a dimensionless metric defined as 2π times the ratio of peak reactive energy stored in the inductor or capacitor to the energy dissipated per oscillation cycle by circuit resistance. Higher Q values produce narrower passbands, steeper roll-off skirts, and longer transient ringing decay.

How do Series and Parallel RLC Quality Factor formulas differ?

In a Series RLC circuit, Q = (1/R)·√(L/C), so decreasing series resistance increases Q by reducing I²R thermal dissipation. In a Parallel RLC tank circuit, Q = R·√(C/L), so increasing parallel shunt resistance increases Q because less current is diverted away from the reactive LC tank.

How are the lower and upper -3 dB cutoff frequencies calculated?

The exact -3 dB half-power frequencies are geometrically centered around f₀ such that f₀ = √(fL · fH). They are solved via fL = f₀ · [√(1 + 1/(4Q²)) − 1/(2Q)] and fH = f₀ · [√(1 + 1/(4Q²)) + 1/(2Q)]. For narrowband circuits where Q ≥ 10, this closely matches f₀ ± BW/2.

What is the difference between a Bandpass and a Bandstop (Notch) RLC filter?

A Bandpass filter passes signals inside the -3 dB bandwidth centered at f₀ while attenuating frequencies below fL and above fH. A Bandstop (notch) filter rejects signals inside the stopband centered at f₀—such as 50/60 Hz mains hum or carrier spurs—while passing lower and higher frequencies cleanly.

How does the damping ratio (ζ) relate to Quality Factor (Q)?

The damping ratio ζ and Quality Factor Q are inversely related by ζ = 1 / (2Q). When Q = 0.5 (ζ = 1), the circuit is critically damped with the fastest non-oscillatory step response. When Q > 0.5 (ζ < 1), the circuit is underdamped and rings for approximately Q / π cycles before decaying to 36.8% (1/e) amplitude.

How does inductor parasitic resistance (ESR / DCR) limit real-world Q?

Physical inductors exhibit copper winding DC resistance (DCR) and high-frequency skin-effect AC resistance (ESR). Because this parasitic resistance sits directly in series with the inductor, the inductor's intrinsic QL = (ω₀L) / RESR caps the maximum Q achievable by the filter even when external load resistance is minimized.

Related & Complementary Utilities

Explore more privacy-first client-side web tools.